Why not?

December 8, 2014

DSCN0940

It’s a 1999 (technically a classic) so it qualifies for the cut-rate trail pass. Insurance isn’t bad, and there was so much snow last March we couldn’t move from the driveway. I chose to frame the purchase as the reaction of a rational man to last winter’s claustrophobia.

10 December, 2014, 9:37 p.m.

It’s impossible to state how much snow there is outside as it’s all drifts and bare gravel on the way to my equipment shed. Suffice it that there’ll be snow in the fields for the Ski-Doo tomorrow.

Today I bought a trail pass online. Now I have to wait until they send the sticker to me, but the Ministry of Snowmobile Trails hasn’t opened them yet, anyway.

www.ofsc.on.ca

11 December, 2014

The recently-purchased Ski-Doo’s o.k. I’ve had a bit of trouble starting it when cold due to flooding. Maybe I’ll try without the choke next cold start.

The ’99 Touring LE offers an excellent ride with good steering which allowed me to follow paths through the woodlot without difficulty. This stands in sharp contrast to the behaviour of its predecessor, a ’76 Alpine, whose single ski worked more to separate the saplings for the massive, pointed bumper than it did to direct the sled. I had found it dangerous to sit on the Alpine’s seat when hurdling drifts, as the landings sometimes compressed one’s spine in a shocking manner. The long-legged Touring acts as though it would prefer a 20-mile run on packed trails to a poke around the sugar bush. It certainly shows more power than I’ll need in the woodlot.

This anti-Alpine will no doubt show its shortcomings in future rides, but for now I like the easy steering and cushy ride.

13 December, 2014

Apart from the use of a spark plug wrench to start the machine in the morning, it works very well. I’m studying everything written on the subject and watching every video even tangentally related to Ski Doo carburetor problems. Some headway has been detected.

The 13.6 mile tour took me across our fields to Forfar, through “town” on asphalt, then onto the Cataraqui Trail, across Hwy 15, and ending at Little Lake, a large pond accessible only by snowmobile.

The skis occasionally ground against coarse gravel on the old railway bed, but the machine’s ride reminded me far more of a Lexus sedan than an off-road vehicle. The hand and thumb warmers quickly warmed up digits frozen on that spark plug wrench.

I discovered that 25 mph is plenty fast enough on a straight, graded snowmobile trail at this time of year. 35 mph is marginally acceptable along a familiar path on a large field.

But the ’99 Ski Doo Touring is surprisingly competent and easy to drive. This has never been more apparent than when I tried to reverse my course. I turned off the trail onto an upward-sloping driveway, then reversed downhill. Starting off on the slope offered a whiff of warm drive belt, but the long sled turned as easily as an SUV and we were on our way home without fuss. A similar move with the intractable ’76 Alpine would have required considerable effort.

A cold start this afternoon brought the machine to life without the use of the spark plug ratchet, so I may yet learn how to operate this promising addition to the Young’s Hill motor pool.

14 December, 2014

This morning’s start with 1/2 choke didn’t work after a 2 second attempt, so I released the choke and rolled it with open throttle for a couple of 5 second bursts until it started. As usual, the engine performed flawlessly, once started.

The Ski Doo passed a milestone this morning when I climbed on behind my fishing buddy Tony for a spin around the field. Online advice had it that the machine was too light for anyone over 200 pounds, though it had seemed pretty good over rough fields with just me aboard. This test was with two passengers, combining considerably more weight than the sled’s modest 440 pounds. The ride was fine. It didn’t respond as readily to steering inputs as with a single rider, but handling was certainly controllable enough for an occasional ice fishing expedition.

Observing the machine in operation from a distance, I was amazed at its quiet. The more we drive it, the better it seems to run.

Next step: installing the hitch and modifying the snowmobile sled we found in the barn to carry a power ice auger and fishing tackle.

15 December, 2014

DSCN0966

DSCN0967

Today I put a fire on in the shop and attended to some of the maintenance tips I gleaned yesterday from a variety of online sources. First was the new belt, which went on easily with the tool I found in the carefully-packed tool case. The old belt’s still in good condition, so I stashed it under the rear seat.

The gear case dip stick had a few filings on its magnet, but the oil looked good, was at the correct level, and I saw no evidence of leaking below.

The main task was to grease the underpinnings, those unmentionable parts only a stern list of must-do’s could make me examine. The manual said to roll the machine onto its side… Uh, I stood on the edge of the running board and pulled on the handle bar, but it didn’t tip, just slammed its left ski down on the shop floor.

Further examination revealed a broken case for the right mirror: I’ll bet I know how that happened. With no desire to do further damage to the rather pristine coachwork on the Touring, I opted to use the system I developed for the 5′ mid-mount mower on my Kubota. The auto lift had no trouble with the weight, and I found three of the (alleged) four fittings under the track. The four fittings on the steering loosened up the my grease gun, and then I let loose with rustproofing oil on the various metal-to-metal moving parts.

The suspension immediately felt less notchy, and we glided fluidly over the local bumps as I put the machine away. Interestingly, the rear bumper now sits at 16″. Before the grease it sat at 17 1/2″.

Over the day I’ve learned that if 1/2 choke doesn’t start the engine, a second or two on the starter with the throttle open will do the job. At least at the freezing point.

There’s a good chance the starting problem is with the operator, not the machine.

UPDATE:  30 March, 2015

The starting problems ended when Cory Sly replaced the float valves in the carburetors (under warranty).  From then on the engine started and ran very well.  It logged about 300 miles on short runs around the property and a few local trail rides.

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: